Drying Cost

Pellet Burner

Now let us go into the details of drying .

We refer to the data gathered during the running of BSR500 in our furnace which channel hot flue gas to drum dryer to dry sawdust .

Below you can find a table which shows our furnace burning wood offcut , wood pellet with Pellet Burner Model BSR500 and compared it with diesel . ( based on calculation )

The table shows that Wood Pellet with the correct Pellet Burner are capable of competing with even the lowest cost fuel  . The reasons are as follows :

1 ) Burning wood are OLD TRADITIONAL METHOD of producing heat , so the efficiency are very low , we gather that if the wood offcut calorific value is 2,500 KCal / kg , the efficiency is only 36% as compared to 80% for wood pellet with the Correct Pellet Burner .

2 ) Wood Offcut have fluctuating calorific value , the feeding would not be consistent , the air fuel ratio will be different , so the worker tend to blow air full blast thus lowering the temperature in the furnace in the end causing higher consumption of wood to maintain high temperature .

3 ) Pellet Burner work exactly like Diesel Burner , it fires when temperature drop to lower set value and stop firing when it reach the upper set value . This will ensure no wastage of over firing or under firing .

4 ) If you have seen worker work at furnace then you will know what I mean with this statement .

" FEED THE FURNACE FULL AND SIT AS LONG AS POSSIBLE " .

 HOW CAN YOU GET EFFICIENCY WHEN THE FURNACE IS FULL BUT NOT BURNING , worst still plenty of smoke will come out from the chimney waiting for DOE to write you a summon . This will also cause temperature to drop until your production are lowered and this cause money too . That is why some company keep using Diesel Burner even though biomass are much cheaper because loss from production are much more higher than savings .

As to the comparing with Diesel you can see the savings come up to 75% . This is a lot of money if you are burning RM100,000 of Diesel per month .

If you are in this Situation , please consider a Wood Pellet Burner :

1 ) Burning Diesel / Gas

2 ) Material Dried not dry enough or not up to specification

3 ) Dryer output too low

4 ) Furnace too small

5 ) Factory space too small for big biomass boiler

6 ) Want to increase capacity of furnace

7 ) Heating / Drying are not consistent

8 ) Shortage of workers

9) If you love mankind , do your part in reducing CO2 increase 

HAPPY NEW YEAR 

LARGE PELLET BURNER

BSR500 Pellet Burner

At last we have arrive at the Ultimate Pellet Burner with European Standard Capability .

When we say European Standard , we mean it , in terms of many facet . It run 24/7 , for many weeks without intervention , just fill up tank , set correct temperature , light up , walaaaaaa . No hassle , no worker   ( " go to sleep if you like " ) , consistent heat output , no smoke , no cleaning and many many more .

BUT MOST IMPORTANT , PLENTY OF SAVINGS .

  
 BSR500

This picture shows a flame of 8 feet height and 4 feet length . The power of this Burner is 500,000 KCal / hour . 

BSR500 Burner features :

1 ) Multi Pellet Fuel

2 ) Automatic Function just like Diesel or Gas Burner 

3 ) Fuel savings of over 50% compared to Diesel or Gas 

4 ) Over 80% Efficiency of energy conversion from Pellet to Heat 

5 ) Robustly Build with minimum maintenance ( no burning chamber to repair )

6 ) No operator needed , just fill the tank and run 

7 ) Quick startup time of less than 5 minute to peak capacity

8 ) Size can be made to order depending on your furnace , minimal modification needed

9 ) High power fuel use lesser storage space , Only option for SME with small factory space

10 ) Very Very clean , no smoke , no pollution 

and many many more reason for you to change to RENEWABLE ENERGY 

If you are doubtful about this burner and supply of pellet fuel , we can supply the burner with fuel and charge based on your usage or fixed monthly rate , we guarantee savings before taking up the replacement of your current burning method .

Currently we have a unit running in Kelantan , firing into furnace . The heat are used to dry sawdust in a drum dryer at rate of 2 ton per hour output . Previously the furnace use wood offcut to the tune of 4 ton per shift of 8 hours , currently with the new burner , the furnace consume wood pellet of less than 1 ton / shift .

Some pictures of the Burner in position firing into the furnace .

Flame in Furnace



Burner Replacing Wood



Burner and Furnace

BIOMASS DRYING

I have touch on this topic in December 2010 in the title of Sawdust Drying . In many cases material needs to be  dried to certain acceptable  Moisture Content before it can proceed to the next stage of manufacturing  . 

In my visits to many plant , I have seen too many mistakes made in the selection of drying system , either wrong fuel are used , wrong design of furnace , wrong design of dryer , wrong design of conveying system for input and output of materials and etc . This mistakes cause many other problems down the line especially during pelletisation not mentioning high cost of drying . Make no mistake , you cannot have good system if you do not have proper knowledge of drying and combustion . That is why drying system are expensive because it will saves you money later and in some cases a matter of do or die . 

Drying Efficiency

Drying for pelleting process are normally done with direct chanelling of hot flue gas into the drum dryer where the hot air are in direct contact with the material to be dried . This process of direct contact are of highest efficiency as compared to indirect heating with a heat exchanger . Depending on material , moisture content of the material and structure of the material , the hot flue gas input temperature can be as high as 800º celcius . The higher the temperature , the faster the material are being dried and you will get higher output from the drum dryer otherwise the drying section will become bottleneck . Consistent temperature from the furnace to the dryer are also important so that the Moisture of Biomass dried is consistent . To achieve consistency and narrow range of Moisture , firing into furnace or dryer need to be consistent , this can be achieve by having good Burner .

Drying Cost

Many  a times this was overlook , everything we sell have a selling price and it also come with a cost . Similarly in wood pelleting , there is cost to manufacturing of wood pellet , and to those who use wet sawdust or even EFB , there will be need for drying , this is one section which is often overlook . Good cost structure will be drying cost of below RM20 / MT of dried raw material . How do we achieve this : 

1 ) use low cost material like timber offcut , woodchip , EFB , Palm Fibre etc

2 ) use high efficiency pellet burner because you are producing pellet 

3 ) do not use electricity , gas or diesel burner , you calculate the cost yourself to find out 

That being said , the planning of Good Drying System is pertinent to keep the cost low so that there will be profit in the selling of pellet . If you dry your material above RM50 / MT then this business will be unprofitable . 

In short it is not easy to keep cost low as currently for any fuel there is cost involved , selection of correct drying system are important .

Drying Quality

During pelleting process , consistent Moisture Content of material input are important to give consistent quality of pellet output , otherwise one minute you will get good and the next minute bad quality pellet . Therefore dryer must have flexibility to ensure Consistent MC for biomass output from dryer .

For your information , any sawdust or even EFB will have sand and stone in it , too much of it will increase the ash content of pellet and thus pellet price will be affected . A good dryer will have system to remove partial of the sand and stone . Removal of sand and stone will also prolong the life of roller and die during pelleting process . 

3 of the above factor are important in the selection of the correct dryer . Wrong selection will cause the followings : 

1 ) Under or Over Capacity of dryer 

2 ) Low temperature input will cause slow drying 

3 ) Inconsistent temperature cause fluctuation in drying thus MC of biomass dried will not be consistent 

4 ) Wrongly build furnace do not give enough heat input to dryer causing under utilisation of dryer 

5 ) Wrong air flow of hot flue gas are not sufficient for drying of biomass 

6 ) Wrong design of input and output conveyors reduce the efficiency of drying

7 ) Non Flexibility of dryer controller make it difficult to get good drying results

8 ) Wrong biomass used for firing , increase cost of drying , whole project not viable 

9 ) Manual feeding of biomass fuel in big furnace are not recommended as labour incur cost and optimum drying are not achieved 

10 ) Inconsistent MC of biomass dried cannot be pelletise into good quality pellet 

11 ) Too much sand and stone will jam the Pellet Mill and damage other parts

and many many more .

Make sure Dryer are selected correctly .

QC and R & D

Quality Control and Research and Development Programme 

Manufacturing is define as : 

The process of converting raw materials , components or parts into finished goods that meet a customer's expectations or specifications .

That being said , I would like to add , to be able to make profit the whole process is a race against time to reach optimum level of operation in shortest possible time .

As of now I believe there are more than 10 wood pellet plant in Malaysia , probably over half have difficulties in producing high quality pellet and running at low efficiencies . Some are not running at all . I admit mine are also having problems with breakdown here and there , but importantly improvement are carried out after each obstacles thus weakness becomes strength .

Wood Pelleting are more an arts rather than skill . There are just too many variables especially for China Made Machines . 

Unless and until you get all the parameter right , it is near to impossible to get high efficiency and quality .

In many organisation QC and R & D are lacking especially in the SME . This is the nature of business as it is too costly to setup and followup . But without these you would be FLYING BLIND , that is what happen and the blame is simple , on the machine . No doubt , China Machine is bad but there are ways to go around to get it better . Unless you are willing to invest in American or European Machines which will cost a bomb .

In wood pelleting , the person in charge MUST be able to setup proper recording so that improvement can be carried out . Proper records are just like a GPS in a foreign country . You use it ( the records ) to see : 

1 ) Who can help 

2 ) What happened 

3 ) Where are you now and where are you going 

4 ) When can you arrive 

5 ) Why things happen 

6 ) How did it happen 

Remember the 5 W's and H

!! GHOSTBUSTER !!  SOUNDS FAMILIAR

Imagine that you are starting , you get into problem , the supplier of the machines did not give correct procedure ( friend , they are seller of machines , they will promise you sky to sell , they are not production man , how do you expect them to give full range of advice when we are paying pittance for the machines ) and your machine are damage or you are running at very low effciency .

What do you do ???

You try and try , after 2 months time loss you give up , losses amounts to RM50,000 or more , you still want to carry on but do not know where to start and when can solve all this problems . Sounds very familiar , it happen to me too !!

What do you do ??? or better WHO YOU GONNA CALL !!! GHOSTBUSTER  , CALL ME .

For now enjoy the song & video .

Word of  Advise , if you are not able to solve the problems in 2 months , it is not possible for me to solve it by phone , it is just impossible , there are just too many parameters and you will need tools to help just like the GPS .

With all the advice and tools hopefully you are on the way for higher efficiency and higher quality of wood pellet . 

Many people called but are unwilling to pay ( no free lunch ) , so advice from the phone are limited in quality , they try the method advised still doesn't work , it won't work , we take 6 months of blood sweat and tears to perfecting our method , so with 30 minutes advise you expect it to work , I wish how simple it is .

In fact I would advise , after you have commission your machine and it does not perform to expectation within 2 weeks ,  better call me immediately for consultation , if not you will lose 2 months at least and over RM50,000 for trial and error . 

WHO YOU GONNA CALL !!!

WOOD PELLET FOR SALE

We now offer wood pellet for sale in the local market .

Price delivered Klang Valley at RM300 / MT in Bulk Bag .

Below are the test certificate and photo of wood pellet .

Call me at 012 9887 118 Lee Seng Ann .

Whole Line Wood Pellet Plant

2 Ton Per Hour Pellet Plant

We are a bit delayed in the installation of our 2 Ton Per Hour ( 2 TPH ) Whole Line Wood Pellet Plant . New date for commissioning have been push back to End of April 2011 .

Lots of minor problems with China Whole Line Design and Installation .

I admit we overlook a few areas and also the professionalism of China Machinery Supplier are in doubt especially in Project Management and also the linkage between each section in the Whole Line Plant .

But in the process we also learn a lot for our future expansion plan and possibly our new 2nd line maybe in 6 month to 1 year time .

We now believe that our pellet mill are one of the best from China and hopefully when it is in production it should give us above 1.2 TPH for the Model 420 unit with minimal maintenance .

Here are some of the photos during installation of machineries at my plant .

Current Pellet Mill / Pellet Mill Plant from China have the following problems :

a ) Pelet Mill Die cracking after short time of usage

b ) Roller Bearing need constant change

c ) Constant Jamming in the Pellet Mill Die Chamber

d ) Low Density of Wood Pellet Produced

e ) Sawdust need additives during production to ensure smooth output of pellet from Pellet Mill

We also found out that many China supplier are not genuine factory owner which means they buy and sell the machineries , thus technical wise they are not up to standard unless they are supplying the best machines from the best fabricator . Normally this is not the case as the buyer will haggle about pricing , therefore the supplier will tend to get the cheaper machines which will create problems in the end . How would you know which is the best machines from China , there is more than 100 supplier of pellet mill machineries from China , everyone say they supply the best . Unless you want to CAMP there to search for the best machines . For the record , I did 3 tour of duty to China to search for the best machineries .

Pre-requisite of establishing a Wood / EFB Pellet Manufacturing Business :

1 ) Stable source of sawdust or EFB

2 ) Total Investment - RM1 Million including machineries , electricity supply , local steel fabrication , forklifts & etc for a 2 TPH Whole Line Plant

3 ) Some technical knowledge on machineries

4 ) For now , market should not be a problem , it is a matter of pricing

Lately ( the last 3 months ) , my blog have generated tremendous search for wood pellet maybe due to the current high price of fossil fuel which at the time of writing , Nymex Oil Futures is at over USD100 per barrel . Inflation in China is also causing a problem as Wood Pellet Plant pricing have also increase from initial RM750,000 earlier to over RM850,000 now , at last count . Sawdust price have also been increasing locally . If price continue to rise , it might not be viable anymore to invest in Wood Pellet Business unless Wood Pellet price play catch up in the near term .